[RESOLVED] DGIndexNV no Output Trimmed TS
[RESOLVED] DGIndexNV no Output Trimmed TS
Working environment is Windows PRO x64 SP2.
The command Output Trimmed TS is not enabled - cannot be invoked.
The command Output Trimmed TS is not enabled - cannot be invoked.
Re: DGIndexNV no Output Trimmed TS
The input file must be a transport stream.
Re: DGIndexNV no Output Trimmed TS
Which one? Or it doesn't matter.
At least, I know mts and m2ts.
Re: DGIndexNV no Output Trimmed TS
DGDecNV supports any standard transport stream. These streams are defined in ISO/IEC 13818-1. Additionally, 192-byte packet streams are supported, where the leading 4 bytes are a timestamp, such as in M2TS files.
Re: DGIndexNV no Output Trimmed TS
Thanks.
Next:
I have used the 64-bit version.
I put a stream from an .mkv file into a .ts file using tsRemuxR.
I had one short segment from the input .ts file outputted into an output file. DGIndexNV didn't add the extension .ts.
While having outputted the next, much larger segment, the program entered some cycle and stopped outputting the stream.
It was modifying the percentage of the job has been done without increasing it. So, there was a blinking 9%.
Next:
I have used the 64-bit version.
I put a stream from an .mkv file into a .ts file using tsRemuxR.
I had one short segment from the input .ts file outputted into an output file. DGIndexNV didn't add the extension .ts.
While having outputted the next, much larger segment, the program entered some cycle and stopped outputting the stream.
It was modifying the percentage of the job has been done without increasing it. So, there was a blinking 9%.
Re: DGIndexNV no Output Trimmed TS
You have to provide a link to a sample TS that I can use to duplicate your problem. Use mediafire.com.
Re: DGIndexNV no Output Trimmed TS
Marking as resolved due to non-response.
Re: [RESOLVED] DGIndexNV no Output Trimmed TS
I'm back with the same problem.
The situation isn't straight.
If I try to output a trimmed file from a source of 27 GB, the processing goes to around 5% ~1.5 GB.
And then enters some cycle.
(I want to trim the first 40 sec. and the last maybe 3 min.)
If I try to do the same with a 10% part (around 2.7 GB) cut from the source the processing is successful.
So, how would you want me to send you a sample TS?
Maybe using a magnet URL (for uTorret) for you to download the file from me?
Actually I try to trim the Rabbit Hole m2ts. So, if you have the move you caould try trimming it.
SpasV
The situation isn't straight.
If I try to output a trimmed file from a source of 27 GB, the processing goes to around 5% ~1.5 GB.
And then enters some cycle.
(I want to trim the first 40 sec. and the last maybe 3 min.)
If I try to do the same with a 10% part (around 2.7 GB) cut from the source the processing is successful.
So, how would you want me to send you a sample TS?
Maybe using a magnet URL (for uTorret) for you to download the file from me?
Actually I try to trim the Rabbit Hole m2ts. So, if you have the move you caould try trimming it.
SpasV
Re: [RESOLVED] DGIndexNV no Output Trimmed TS
OK, I have easily duplicated that. Investigating...
Re: DGIndexNV no Output Trimmed TS
I have slipstreamed the fix into 2039, so redownload it and update DGIndexNV.
Thank you for pointing this out, SpasV.
Thank you for pointing this out, SpasV.
Re: [RESOLVED] DGIndexNV no Output Trimmed TS
Thanks,
it's good now.
it's good now.